How to make a Bead of Marigold Flowers

Summer has come to an end, many flowers have faded, and therefore saving the variety of natural colors gradually subsides. But as long as the fall is not fully come into its own, you can still enjoy the latest colors of the season. One of the few flowers that still we are pleased – it marigolds. So what exactly it today and we’ll weave.
We need:
– beads № 11: orange, yellow and green,
– wire diameter 0.2 mm
– green thread for winding leaves flowers and stems.
As a model for the production of marigold Bead here I took the flowers, which are now in full bloom in our yard.

Each of our flower buds will consist of 4 petals series.
The first row will be the smallest petals. To take them 35 cm long, and the wire is first typed on it 5 yellow beads.

We place the beads in the middle of the wire, and then the loop consists of beads and twisting the wire underneath 2-3 turns. Thus it is necessary to loop of beads turned around in the middle of the wire.

Further, at each end of the wire adjacent to the first loop should be done even for one the same eyelet of the beads. Choose any of the ends of the wire, we collect it 5 yellow beads

and twisting one loop, placing it almost came to the first eyelet.

After that, another exactly the same loop of the 5 yellow beads do at the second end of the wire.

It remains to twist together the two ends of the wire – the first series of petals ready to bud.

For the second series of petals take the wire length 60 cm. First, the wire 5 recruit orange beads and twisting of this loop, placing it at about 15 cm from one end of the wire.

All further weaving are conducting only at the long end of the wire. We recruited him 12 yellow beads,

we add these beads arc over the first loop,

We pull a wire to the beads formed close to the first eyelet and twist the wire 2-3 turns. We get a second loop, located on the first flush. These two loops will form a first flap of the second row.

Next, in the same – long – the end of the wire is necessary to weave more of the same 5 petals. For the first tabs of the second tab is typed on a wire 5 orange beads

and twisting one loop, placing it at a distance of about 5-7 mm from the first petal.

Then, the wire 12 is typed yellow beads,

We add up these beads arc closely above the first lobe and the second loop wire twisting 2-3 turns. The second petal ready.

Similarly, we are continuing to weave at the long end of the wire the same pitch. Note: Because the beads may vary slightly in size from each other, it is possible for the upper loops must be taken not exactly 12 beads, and a little more or, on the contrary, a slightly smaller number of beads. The exact number of beads is not critical; but it is important to make sure that the loops in one lobe are disposed closely to each other, wherein the petal to look smooth, and that the upper eyelets on the wire were not visible voids.

Gradually, as the number of petals intertwined, we can see that the petals start to like “crawl” on the edges of each other – this is normal; With this arrangement, the petals of the flower bud will collect much simpler than when there is a distance between the petals.

Total for the second row has to weave on a single wire, 6 petals.

To petals woven series are not lost, just join them. Take the first row of petals, insert it into the middle of the second row of petals

and twisting together the ends of the wire. In this case, the pitch of the second series of circumferentially uniformly distribute that between any adjacent petals was the same distance.

We leave for some time to get part of the bud and proceed to the weaving of the third row of petals. To take it a wire length of 80 cm. 6 petals must weave on this wire. Petals weaving technique – is the same one we used to weave the petals of the second row, but only one lobe of the third row will consist not of two but of three loops.
Making the first petal: its first loop consists of 5 orange beads. This loop, as in the second series weaving beams, in place of 15 cm from one end of the wire, and further braiding are conducting only at the long end of the wire.

The second loop lobe consists of 12 orange beads.

The third eyelet 19 comprises a petal of yellow beads.

The remaining petals similarly. The first loop of each next lobe (5 orange beads) are placed approximately 7-9 mm from the previous one lobe.

The second loop in each petal of this series consists of orange beads. A number of beads, as I noted earlier, is approximately equal to 12, but may be slightly different.

The third loop in each lobe of the current series consists of yellow beads (standard – 19 beads).

Thus only this wire 6 petals for the third row of the bud.

After the completion of the third row of weaving petals attach it to Bud: take already joined together the first two rows of petals, insert them into the middle of the third row

and twisting together the ends of the wire. The pitch of the third row, as usual, is uniformly distributed over the circumference.

Side view of the bud at this stage:

Next, we do the fourth row of petals. In this series, all the petals are also the same, but they are lagging individually, so each petal take the wire length of 40 cm. The petals of the 4th series are very similar to the petals of the third series, the difference between them is very small.
First, we make the first loop – it consists of 5 orange beads. As each petal separately, the first place on the middle of the loop wire.

For the second loops to choose from two ends of the wire shorter (if both ends of the wire exactly the same, then choose any of them), and recruited him 12 orange beads.

As usual, we add these beads arc closely over the first loop

and twisting the wire by 2-3 turns.

For the third loops, select the longer end of the wire and recruit him 19 yellow beads.

Bend the end of the wire with beads of arc recruited over the second loop,

and tolerate the other end of the wire through the last dialed bead.

Tighten the wire making sure that the yellow beads formed the third loop of the previous two,

and then twisting together the two ends of the wire. Petal ready.

Total for the 4th series bud needs to weave these 8 petals.

After all 8 petals are ready, we collect them together. To do this, take the length of wire 30 cm long and consistently “stringing” him all the petals of the 4th row, passing this piece of wire through the yellow bead, located at the base of each petal.

We pull all the petals close together, align the ends of the additional wire and twisting them together with a few turns. Please note: we now only curl the ends of the additional wire; the ends of the wires coming from the petals until all together do not twist!

Next, we place a bud on the desktop so that the upper part of the bed was directed to a table and straighten towards the end of the wire coming from the petals of the 4th series (of each petal there is a two twisted with each other end of the wire – to untwist them is not necessary). On each such pair of ends of the wire extending from the petal, dial 8 green beads. Similarly, we proceed with an additional wire, which collected the petals of the 4th row. Total for each of the 9 pairs of wire ends need to dial 8 green beads.

Putting it all ends of the wire together and pulls all the green beads close to the bud.

Check to the fourth row of petals was a close 3rd near the petals, and then twisted together all the ends of the wire from the bottom of the flower.

Flower bud ready. We leave it for a while and move on to the production of leaves.
The leaves of marigolds – components; Each sheet consists of numerous narrow leaves: central and located them pairwise multiple rows of the same leaves. In appearance marigolds leaves are very similar to the leaves of mountain ash. Since our website is already a master class in weaving rowan beads, then we will do the leaves of marigolds on the already known scheme. So we go here on this link (master-class will be opened in a new tab) and make the necessary us the number of leaves. Note:. For every little leaf rowan we take the wire length of 25 cm for leaves marigold same will be enough to take the wire length of 20 cm (you can even slightly less, but in a very short wire is inconvenient to weave).
The number of leaves that need to weave for each flower, depends on your desire. The more leaves, the will be more lush look ready bouquet of marigolds. I recommend for each flower to make 3 or 4 sheets.

After all the leaves are ready, we proceed to the final assembly of the flower. First we take the green thread and winding them petiole of each leaf in between and still leaves about 2 cm after leaves.

Then, the same green thread winding stem of the flower bud under approximately 3 cm in length.

Now we take one sheet and attach it to the stalk by the same thread.

Continue winding stem thread More approximately 2-3 cm, and then using the same thread to attach the stem another sheet.

Thus gradually attach to the stem all the leaves (this implies that the leaves were placed on the stem circumferentially) and the winding stem green thread over the entire length.
To thread not dissolve, tying them for a couple of knots. If necessary, trimmed at the bottom left of the stem ends of the wire.

One flower is ready! I made three of the flower and the resulting bouquet of marigold put in a vase.

courtesy: mirbisera

Leave a Reply

Your email address will not be published. Required fields are marked *