How to make beautiful doll umbrella

doll umbrella 1

I hope I have not bored you. Just now, when I’m trying to make something, I take pictures of the process. Sometimes it works, sometimes more or less something out. So today- umbrella. Hopefully useful.

Required Materials:

  • Airball (pictured him there, the cat dragged after I took it out of the umbrella),
  • PVA glue,
  • toilet paper,
  • brush,
  • thread,
  • paint,
  • glitter,
  • napkin for decoupage (not necessarily),
  • the wire

DIY: Pineapple from the bottle

PINEAPPLE FROM THE BOTTLE 1

Material:
1.corrugated Paper,Glue,Bottle

– Upper lobes cut out a shape, a width of approximately 1.5 – 2 cm and a height of 7-8 cm. Sami scales width of 2 – 2.5 cm long and 9 centimeters folding is not necessarily in the middle, the best one the tip of the other shorter. Fold paper twist and stretch at the bend locations at once 2 halves. Inside, between them I have them stick together with glue droplet. If the scales are short, we will see the bottle and turn ugly. That begins wrapping the bottle in a checkerboard pattern. Top tip – do not tear off the label !!!! To bare the bottle very hard to stick (especially Italian crepe paper). Bad assistant with the paper and tape !!! Of course, if you use an ordinary crepe paper for school (I did a paper Christmas tree) is suitable glue pen and tape. The second pineapple glued Melt – quickly and accurately !!! Often, i.e. rows close to each other to stick is not necessary – it turns dumb Optionally, you can paint the finished pineapple marker And it is possible, and leaves from the bottom, “attach”. Beauty Get pineapple bottle low, a round. That such leaves I made soapstone pallet.

Beautiful butterfly wall art

Butterfly wall art 1

Items we need Double side tape, Pencil, Scissor, Chart paper of any color or as many colors as ur wish. U can make it colorful too. Here I m showing u method of a bigger butterfly.Cut a piece of chart paper 10* 10 cm. Then fold it from middle Then draw half of butterfly design using a pencil. It will be the back portion of a butterfly. Then cut like this. Open the butterfly, n do finishing. Take 5 cm double side tape Stick this double sided tape on back part of butterfly like this, covered double side tape should be used to stick this butterfly on the wall. Once u make all the butterflies. Then u can paste these on the wall at one time. Make any design using these.Butterfly wall art, around 60 butterflies of different size. I used smaller butterflies in making the tail of heart. Then remaining used in ascending order.

How to make quilling frame of cardboard

Quilling frame of cardboard with his own hands for a photo 1

Photo frames can be not only a good interior decoration, but also a wonderful gift close. They can be bought in any store or made from scrap materials with their own hands. The most available material, in this case, can be regarded as paper.

What would have been our quilling frame of cardboard with his own hands for a photo, we need a multi-colored cardboard, glue gun, glue PVA, stationery knife, paper quilling, quilling tool for.

We start with the fact that the inside of the draw colored cardboard the size of our future scope of the decor. Then take the knife and carefully cut the frame. Now we need to take the glue gun and glue together a piece of cardboard and a blank for the frame. Apply glue should be at the very edge of a board that had a place to put pictures. What’s more, plus the use of glue gun, it creates a small space between the sheets of cardboard, where he will continue to post pictures. Now you need to make a stand for the frame. To do this, take the cardboard and cut the shape out of it as shown in the photo. Bend the edge of the figure so as to remain within the middle of a width of about a centimeter. On the back of mid-Apply glue and glue the base to the frame. Now we can proceed to the decor, which is made in quilling techniques. To do this, we need to take a quilling tool. If you do not exist, it can be very easy to do out of the ordinary toothpicks. To do this, take a knife and carefully cut the edge of the toothpick. The tool is ready. Now we start to do the flowers for this we press the edge of the paper to the toothpick and turn loose circle. Then presses one edge of the circle to get a drop. This will be our petals. Do not forget to glue the edges of the paper PVA. With the help of glue, PVA collects flower of six petals and decorate the middle of a simple yellow circle. Sticking flower to the frame. Making other flowers. To do this, twist the loose circle, and then Fold the two edges up, pressing the middle inside. We supplement this flower with green leaves, drops and connect it with another flower strip of green paper. In the same way, we do the flower of a different color and fasten it at the top of the frame. Of the green paper, folded together a few times, do list, which is attached to the bottom of the flower and composition complement one another leaf and twig. We glued together several strips of green and fasten them to the bottom of the flower. Fold the branches, simulating the vine. Do not forget to capture all the glue. At the edge of the upper twigs fastened little flower from simple circles. The frame is ready. If you wish, you can complement the decor more details.

How to make micron cotton toys

micron cotton toys 1

I remind you of what you and I have started to work. Our basis for ladies and dry we proceed to the formation of clothes.
Please do the bottom (skirt-dress), and her top dress coat.
Just want to clarify the main points of how I work with wool, which would then not be repeated. I form the necessary me the details of the dry wool, and then brush with glue (abundantly) Smooth to the base, at the same time, if you need a flat part is on the hand press, and if you need a bulk item, brush lightly touches wool (only for that would leave her glue).
Of wool strips, I form a semicircle and smooth brush to skirt basis. At the base of pressed and left on the edge of the volume. Such cylinders dialed as much as you want. The lower part of the cover with a piece of cotton wool and smooth, that would be the bottom of the toy so it was neat. The top coat, I plan to make the folds so I form them from dry and smooth wool brush with glue, while at the crease did not click, but I press on the sides of the brush, that would be visible pits folds. I do as much as I would like folds. Whatever wrinkles are not looked rough, put a plate on top of wool and smooth, pushing the brush only in the pits At the top of the reservoir and put a smooth, pushing the brush continued folds (remember that always brush glue) ven.
On the front of the coat do two rollers left and right and also smooth brush: press on the sides and in the center leave the volume, ie nano she glue and a brush are not pressed. Suspended on a rope -Let dry. Similarly, we are working with the second figure. Explanation of the same so followed by a photo without the text. The skirt folds. Just send out to dry. In the third all the same: only rolls and folds distribute differently. So you can think of many options combining the folds and ridges.

All the basics were sent to dry well and will continue to work tonight.

All good mood and success.