Epoxy resin (Resin Crystal) Silicone Mold, the basis for the ring, the metal figure of the Eiffel Tower, pliers, wire cutters, glue, epoxy, matches, jewelry wire, sequins or microbeads, breadboard knife, a plastic cup and a wooden stick.
Epoxy mix in the proportions 2: 1, 1 ml and 2 ml hardener resin
mix thoroughly
We pour resin into a special silicone Mold covering approximately 1/3 of the total Mold resin and give leave all if it does not, you can put the MDL with the resin in a container of hot water
take further action figure of the Eiffel Tower and bite off the ear with pliers, wire cutters, if it did not work very smoothly, you can trim the metal nail file
then take the match and cut off their head sulfuric Prototyping knife, so as to obtain three flat, small cubes
then do the design for securing the tower of matches and wire
anchoring wire
and immersed into the resin, so that legs of the tower structure and it does not come into contact
leave to dry for 24 hours
after this time, we take out the design and our tower remains fixed in the resin
Now to refill the resin, so that it almost covered the legs, this point is very important, because if you pour the resin, your tower will remain hanging in the air, and if you do not top up, then you will not see her legs, you need to be very careful at this stage, because Mold matted and filled up turret trio predict the result of the feet.
after you have filled in the resin again, we leave it to dry for 24 hours, and do not forget to cover the MDL cap to the resin did not get small lint and dust
After 24 Sasa pour in MDL sequins, artificial snow or microbeads, so you can pour white baked plastic rubbed on the Needle or fine saw, but the process is quite time-consuming, this advice find artificial snow if you are not a fan of sequins, I used pearl white tinsel
Now fill it with epoxy resin to the top and leave to dry for 24 hours
As time passes, we take out our balls mold. what we’ve got
then take the epoxy adhesive and glue bead to the base, the base can be any brand, it depends on your imagination, in this case, I used 2 silver and bases of round oval. you do not have an epoxy adhesive can be stuck on the same pitch, just a little wait until it thickens to not let stains
leave to dry for 24 hours.
Our ring ready
I hope the workshop seemed to you accessible and interesting and useful to you in the future
The bottom of the tube 4 on 4 weave rope. But it does not matter. Choose your size and your type of weaving. To have a form, I turned the fungus had a plastic leg, just as the size of jars and bowls, to him a bowl and top braid. Spun upside down, so it is more convenient
So I whip. It is filmed from above. Braids press my knee. I still weave on the floor and pressed his knee. And that I do without him? On the occasion of shooting my new socks. Entwined in the bowl 6 rows, then we’ll narrow weaving
Jar of raspberry Kampot cargo. Stands run into the bank and weave more rows 6. Malinka this release.
I changed to a smaller bank. For this, I go to a friend of the milk cow.
That’s about cauldron. While stop.
Pierce tubes of three pieces for each second small stands. For in the interval between the posts had one braid. Ideally, the two should be, but not thin braids, the paper they are not fit at all, so it is so.
We are pushing the netting with scissors. so it was obvious where the tube to shove
This is the view from inside. really beautiful?
To increase the tube and decided to braid pigtails. tubes soaked waters. I decided that it would be easier and simpler. I honestly waited a couple of minutes and-and began to weave. Paper during the weaving just rolled off the tubes, pigtails obtained ugly, had to wait for the complete drying and weave on. I’ll tell you honestly, Dasha weave easier than this cauldron.
Again, all turned and began to fold pattern of braids. A bit like the head of the Gorgon Medusa Mikhailovna, so if you need to -bite for the theater as an idea, I do not mind.
He twisted and missed all of PVA. to grab
Then I cut the butt with braided and glued. Pins for the fortress.
We continue to weave on, but with the difference that it is necessary to tighten the rack on the side.
Here’s a turned collar. it was convenient to weave, I launched a working tube in the opposite direction. To make their favorite Bending
It is on the cover. , Further, dilute the rack and weave plate.
In the middle of the weave is necessary to add another one to every small stand
The finished result, you have already seen. Scold not necessary blind! she can see that the curve, but I do not teach how to make crooked, I write, what not to do.
How to make a lamp Halloween with your own hands. For work, we need the following materials:
Glass containers – jars of different sizes;
Acrylic paint is blue or purple color (you can use a car spray paint);
candles tablets;
black paper;
Printer and printer paper;
scissors;
token white glass;
PVA glue or hot glue.
Getting Started. My jar under hot water, removing labels. Dry them and then paint or acrylic paint-spray.
Next, print out on the printer of any of the templates below to transfer the black paper and cut out. Glue to the jar with white glue. Where necessary to paint on a white marker. At the bottom of a lamp put a candle ready-tablet. Voila)
Today I’ll show you how to decor elements help from fusing to decorate the interior,
it can be any cabinet doors, mirror, tiles or window,
this will require the case, the new items that you can buy from me in any quantity and desired color scheme and glue.
I bake them of arbitrary shape, you need to put your own picture,
all who are able to come up and draw a branch with flowers, it will not be difficult!
Only imagination !!!
All photos were taken a year ago when I repaired my apartment and preparing for the decoration of kitchen units, so do not be confused by some of the details …….
in the photo clearly shows that the kitchen in the process …..
so look “parts”
and such!
Further,
I had 4 glasses,
almost simultaneously laid out drawing
Whatman is under glass, on a white background layout makes it convenient, but it is an old sketch,
it did not pay any attention,
again I note that all took place in the “martial repair conditions”
that was at hand, and then went to the cause, even the glasses are not on the table, and removed the door!
it was my table a few months ……
and stood on the boxes with things !!!!
the whole picture, I first laid out, and then pasting.
Use professional adhesive for glass UVR,
it can be replaced by a transparent adhesive or sealant for glass
all is ready!!!
glass furniture manufacturers have given,
they inserted them into the doors and lockers ready brought to the assembly.
………. Slightly “missed”:
TIP !!! better to make glass with the back of the mat, as everything inside and then knocks,
I came out of this position by gluing the back matte film.
and so…….
beautiful, and most importantly you will not be bored interiors!
Let your home be sure with his zest !!!!!!!
Getting Started. My jar under hot water, removing labels. Dry them and then paint or acrylic paint-spray.
