How to Make ” happy Chef ” Clock

Watch “Happy Chef” with the décor and the pendulum of salt dough.

1. Draw a sketch. If the round clock (as in the photo) encircle the circumference of hours on paper. It is the center of our composition 🙂 And then we draw our chef as if he comfortably sat. Telo cook should find little in the circle so that later it was for that stick to the face of our Povarenkov! (All parts of the body) Just pay attention to the arrows. Mark the circle endpoints to reach that of the arrow so that they can move freely and cook figure they do not interfere. I had a long arrow slightly undercut. It is better to use the little arrows. Now on sale, you can pick up a variety of arrows for hours. There are arrows in the form of a fork and knife! Goodwill draws a sketch. Note that one leg will cook pendulum. A second elongated at the bottom of the dial and covers the fixing of the second leg to the base of the pendulum. (Think about these details in advance!) What would have turned out that mounting the pendulum to be seen? When the sketch is ready, you can continue! Sketch we get on the scale of 1: 1

2. Take the tracing paper and translate drawing on tracing paper.

3. Next, cook salt dough! In 4 of the salt ( “extra” small), 2 parts water, you can add 1 teaspoon of wallpaper paste (dissolve in warm water). And knead the dough, gradually adding flour. The amount of flour on the experience difficult to define at once, and it makes no sense just to fill a lot of flour, gradually add to that condition until the dough becomes like plasticine. Here, of course, you need a little practice. One thing I will say is necessary to knead the dough long and hard, the longer you have it hesitates, the more plastic it becomes! It can be constantly wet hands if you feel that is not enough water. In principle, it is possible to replace the salt dough polymer clay or plastic, now it is good enough, and the blind cook from it.

4. The dough is ready. Wrap it in cellophane and pinch off a piece to the rest of the dough does not dry. Take a pan, put it on our tracing and start sculpting! Torn off a piece of dough about this so that we have enough to make the body! Moistened hands (which is easier to work) crumble in the hands of a piece and give it a shape of the body.

Lek in front of your eyes is a drawing on tracing paper. Apply the item to the drawing in order to accurately get into proportion. The body is ready. Further, sculpt shoe (are putting to the templates), the second shoe do. Then sculpt the foot – leg and the left foot with water glue on the edge of the leg slipper. All we do in the templates! Using a knife, you can give the crease in his trousers. Just Do the second leg, we sculpt it separately from the cook to the side as it is a separate element, a pendulum. Similarly to impose shoe with water the second leg, as in the photo.

Then do the hand (first hand, and then impose them on the sleeve). Then the head, then the cap. Next came the small details. Buttons. Oh yes! We forgot the apron! Roll out the dough thinly, cut out a rectangle. The edges of the hurting, the bottom made wavy, apron and top, on the contrary, is gathered! Remember the childhood sculpting from clay! Moisten the body cook out there, where it will be a little apron with water and attach the apron top, as in the photo. Surplus clean. From tony use, Koy flattened sausage dough. Do the same with a handkerchief. To finish the details. Ears, nose, hair, laces, beads for the dial (I did both the cake roses and leaves and buttons just like in the photo). Just do not forget to make a wire holes antennae! (Which we then make of the wire and glued into these holes)

5. Oh, and we forgot the cake! In one hand, our chef holding the cake. With a plate of sausages does on the hand, then he cakes and decorates his balls, cherries. You can instead of cake, think of anything! Check if you have forgotten some details?

6. We put our cook in the oven! On low heat, 50 degrees, we dry our figure to rosy color. It may take a long time (it all depends on your oven, so you need to keep the process under control!) The first-hour look into the oven when the temperature is too high a figure may swell! Avoid this if for the first-hour figure has not changed, then all is well and you can add the heat to 100 degrees and raise the temperature gradually to the dough a little bit browned! Most look into the oven, so as not to burn! Once you see that the figure was the rosy cream (like the face and hands in the photo), you can pull the product out of the oven. Allow to cool completely hand-made article, it is better to continue to work the next day.

When the figure has cooled down, you can start to paint it with acrylic paints.

8. Next, Let us watch. Select a card or a napkin decoupage you like (von hours which you have in mind, as the stripes in this case).

Glue the background on the basis of hours. “Substrate” with a sponge and acrylic clock edge. You can even sprinkle on the surface for an even more powerful effect of aging (at the bristle brush a little paint recruit and hold your finger on the brush at the level of the dial spraying paint on the surface of small droplets). After drying cover any acrylic paint.
9. Our chefs are glued to the dial on the indispensable glue “moment” of the second leg of glue to the base of the pendulum. Mark up where will our roses and leaves on the dial, glue, and so does the rest of the mark (as pictured). Here is our watch and we are ready!
10. The only center of gravity of our watches can be removed (as the figure is more than the right), so the clock should be secured to the wall in two locations, how do I, or attach the other side of a counterweight-bob to the reverse side. We attach our pendulum. And the clock ready!

DIY Butterfly Clock Wall Art Tutorial

This crafts project shows how to make a butterfly clock wall art. Creative DIY idea to make unique piece of home decor with your own hands! It will look fantastic on your home wall. You can make colorful butterflies to decorate kids’s room. Let’s try it.

Required Material:

  • A piece of black cardboard;
  • Card stock paper of various colors;
  • Utility knife, scissors, ruler, pencil, compass;
  • Glue;
  • Clock movement mechanism.

How to make soft pot clock ornaments

The main thing – the idea! You can make such a clock of any size, not just covered with clay cup, but any size jar, pot, bowl …

1. Choose a large ceramic cup on the big, down on the table. 2. Take a piece of brown Taiwan Zhengguang soft clay, with rolling pin (or pressure machine) even carry out a slightly thick piece, wrapped in the cup outside the wall. (Note: Do not put the whole cup full, but more than 1/2 of the area, so as to ensure that the clock can be done after the stand.  3. Wrap the cup wall, find a center point poke a round hole, the size of the round hole with the shape of the core size of the circle as much as possible. 4. With scissors empty beer cans cut into about 3mm of the strip, around the outer wall of the soft clay, this is the use of aluminum toughness to prevent the soft clay in the dry nest after the deformation of the phenomenon. 5. and then pressure a layer of the same size before the brown mud, the purpose is to cover the beer cans, pay attention to poke out the hole. 6. Then, with some small mud in the brown mud surface to do the shape, small mud from the bottom to the formation of gradual color is more beautiful. (The second line, white plus two brown; the third line, white plus three brown, and so on until the whole cup wall.).  7. Put the affixed work into the oven and bake at a temperature of 120 ° C to 150 ° C for about 20 minutes. To be cooler oven, the work out, find a flat head long strip of the tool, slowly let the soft pottery from the porcelain surface. 8. The general effect of the concept bell came out. Then please carefully observe the shape of the clock, the arc is greater than the cup 1/2, whether standing secure. 9. Prepare the watch core. 10. The core through the round hole, with a special screw on the back, the back into the battery will be able to time it!

DIY: Handmade Wall Clock

You can make at home a beautiful and unique handmade wall clock. And remembering that you do not need to make a colored piece, you can make a piece with unique color.

To make this part you will need:

  • Ruler;
  • Wooden board or MDF board;
  • Electric saw or saw;
  • Sandpaper;
  • Cleaning cloth, very clean and dry;
  • Wall clock machine with hands;
  • Drill with specific drill for drilling wood;
  • Wood sticks;
  • Cutting Pliers;
  • Common brush;
  • Acrylic paints with the colors of your choice;
  • Pencils for joiner.

Start by separating all the materials that you will use in your work.

Then draw on your wooden board or MDF board the shape you want for your watch, with the aid of the joiner’s pencil and a ruler. Afterwards, serrate around the contour drawn, in a round shape or in the format you want, and draw the numbers of your watch. Now drill your watch numbers with the aid of a drill with a specific drill to drill wood. Then keep drilling the numbers. Just after you’ve drilled all the numbers, scratch your watch. And drill a hole in the middle of the piece. Now, clean your part immediately afterwards with the cleaning cloth, very clean and dry, to remove all dust. Then place wooden sticks in the number holes. And mark where you are going to cut them. Then cut the wooden sticks. Now, paint the tips of the wooden sticks with the colors you want. Then, to finalize your piece, simply attach the wall clock machine with hands. And it’s ready!

DIY Coffee bean clock

How to make coffee bean clock

hours, was born from a great love for coffee and chocolate 🙂
Thus, the coffee and the sweet tooth will need:

– Preparation hours under a coffee cup. My size is about 17 * 22 cm;

– Napkin in a coffee theme + brown or maroon monochrome napkin;

– Clockwork;

– Acrylic primer, varnish, paint brushes;

– Acrylic paint: white, brown;

– paper towels;

– polymer clay;

– Potal and glue Potali;

– satin ribbon;

– coffee beans;

– Melt;

– PVA glue;

– Foil.

I inspect the workpiece, looking for defects and fillings eliminate them. After drying the skin. On my billet was more master ordered 3 small holes on nizu- for greater beauty, decor

Then, in the course is the ground, I put or render it with a sponge. The soil dries very quickly, and check if everything is dry, skin in 20-30 minutes. The next step – applying acrylic paint with a sponge or sponge evenly in 1 or 2 layers with drying. The paint I take in DIY stores: waterborne acrylic for interior use. 0.8-1.0 kg buckets on long enough. On my watch, two coats of acrylic paint well dried and now akruratno, without fanaticism hides. We need a perfectly flat, smooth monotonous white surface. The skin initially the average grain size in the end, a smaller, more gentle I picked up a napkin here: solid coffee with a small inscription. My billet quarter cloth covers not fully, the handle on the big cup, I rep later.
I’ve found method allows to stick a napkin neatly, without folds or tears. The top layer of paint wipes placed face down on the file and poured a puddle of water. While the water is distributed on a napkin, dabbing her napkin neatly straighten slightly stretched it sideways. The fingertips are helping to do this quickly, but carefully.