How to make newspaper tubes frame

frame from tubes of newspaper 1

Cut the cardboard box. Keep in mind that inside, somewhere in the 5 mm on each side, the frame will be wider by tubes

Flatten with your fingers and sticking the tube from the inside. Here I posted a lot, then remove excess glue and. It is necessary to glue from a distance of 1 mm from each other. I put on top of the load and wait until post

bend the tube at the front of the frame and begin weaving. Promoted through a tube. Next staggered following

So I put my hand and pushes the next tube

I continue marginalia on the width of the frame.

Entangling is also the other side, the same Kol liches vom horizontal tubes.

Now I take my top.

Cut Sredinka and sealed all the tube inside out.

I paint the finished frame. I walked on top of a gold acrylic paint dry brush. On the reverse side to stick the same cardboard box and paint

How to make fun giraffe from newspaper tubes – Step By Step

giraffe from newspaper tubes 1

From cardboard cut out of the sheet blank. We attach tubes – rails and begin pletenie.Dlya smoother braiding each tube add copper wire.

Scourge of about 14.5 cm and remove the wire karkas.Teper body will expand.

After 8 propletennyh series, we begin to develop head and neck of a giraffe.

Separately weave ears, horns, and nose of a giraffe.

Decorate zhirafa.Szadi we stayed korzinka.Ee can be left unchanged, but you can close the carton and place the back of a giraffe.

Glue eyes, fur, nose, and mouth.

How to make pot from newspaper tubes – Step by Step

pot from newspaper tubes 1

The bottom of the tube 4 on 4 weave rope. But it does not matter. Choose your size and your type of weaving. To have a form, I turned the fungus had a plastic leg, just as the size of jars and bowls, to him a bowl and top braid. Spun upside down, so it is more convenient

So I whip. It is filmed from above. Braids press my knee. I still weave on the floor and pressed his knee. And that I do without him? On the occasion of shooting my new socks. Entwined in the bowl 6 rows, then we’ll narrow weaving

Jar of raspberry Kampot cargo. Stands run into the bank and weave more rows 6. Malinka this release.

I changed to a smaller bank. For this, I go to a friend of the milk cow.

That’s about cauldron. While stop.

Pierce tubes of three pieces for each second small stands. For in the interval between the posts had one braid. Ideally, the two should be, but not thin braids, the paper they are not fit at all, so it is so.

We are pushing the netting with scissors. so it was obvious where the tube to shove

This is the view from inside. really beautiful?

To increase the tube and decided to braid pigtails. tubes soaked waters. I decided that it would be easier and simpler. I honestly waited a couple of minutes and-and began to weave. Paper during the weaving just rolled off the tubes, pigtails obtained ugly, had to wait for the complete drying and weave on. I’ll tell you honestly, Dasha weave easier than this cauldron.

Again, all turned and began to fold pattern of braids. A bit like the head of the Gorgon Medusa Mikhailovna, so if you need to -bite for the theater as an idea, I do not mind.

He twisted and missed all of PVA. to grab

Then I cut the butt with braided and glued. Pins for the fortress.

We continue to weave on, but with the difference that it is necessary to tighten the rack on the side.

Here’s a turned collar. it was convenient to weave, I launched a working tube in the opposite direction. To make their favorite Bending

It is on the cover. , Further, dilute the rack and weave plate.

In the middle of the weave is necessary to add another one to every small stand

The finished result, you have already seen. Scold not necessary blind! she can see that the curve, but I do not teach how to make crooked, I write, what not to do.

How to make a ship from newspaper

ship from the newspaper tubes. 1

Required Materials:
– Newspaper tubes
– Gafrokarton
– Electrodes
– Transparent glue gun
For starters are forming a bottom. Cut from two pieces and glued together, then pressed his press.

Cut out two more pieces of the same shape, but slightly smaller and gluing. It will bottom.

Cut out more Fourteen pieces of eight-by-ten centimeters and glued together seven pieces.

Paste them on top of the bottom.

Turn it upside down and press down the load so that it is better to stick together.

Takes two electrodes and they pierce the deck.

Then wrapped with newspapers electrodes.

Poured into the holes from the electrodes hot glue and insert to the electrodes.

Then embark on a weaving. Insert the tube into the bottom.

Pick up small stands.

Weaves a string four rows of two tubes.

In the fifth row and add a third straw weaves a rope of three tubes.

Propletaete few more rows to twist got out on deck. Getting to the weaving poles.

Two tubes twist around the electrodes. Then you make the observation basket. The author has shown two options. First, you can start to weave a piece of string around the remaining tubes.

The second option is to wind-blown tube around the electrode.

At the stern using toothpicks are doing holes.

Then pour in the hot glue them and insert the tube.

Now leading tubes weave only the stern.

Deck Wallpapers light tubes.

On the nose put another electrode and wrapped his brown tubes.

Then start weaving the bridge.

Skirting beautiful finish crimping of the two tubes.

Like this, as the author pointed to the picture should look like a ship.

A proplatelet couple of rows, and then paste a piece of cardboard.

Top cover her with boards of tubes.

Front ends of the column.

At the rear are building a railing.

Cut off all unnecessary and stain.

To attach the electrodes on the two newspaper tube.

From white tubes kite guys.

Another time to stain stained with glue.

To make a sail.

Sizing them on both sides.

Cut off by the size of the sail. The ready tube that will keep the sails.

Glued to the tube sails.

Attach the sails to the newspaper ducts.

Make brown tube wheel.

Then you make a triangular sail.

Glued all the sails to the ship.

Here and ready to ship.