How to make small houses with tiled

Small houses with tiled 1

Hello, my dear !!!
blindly here such houses. Height 12 cm and 10 cm. Now wander. The windows. View from above. And on top.
Then I will try to show in detail how I made a house a little more. Little by analogy, only the roof easier.
Also, I’ll show you my experiments with shingles, I hope that will come in handy !!! Required Materials:
– salt dough
– cardboard
-marker (or pen or pencil)
– masking tape
– scissors
– stack
– line
– useless little box (can be made of cardboard)
– cold porcelain
– lace (for little houses)
– eggshell (for a small house)
– paint
– paint
– brush
– PVA glue and resin
– toilet paper.

Let us proceed. I took the box from under the cream. It is necessary to measure the width of the wall of the house, and all the walls should be the same size, that is at the base of the house should be square (it is necessary to make a roof).
You can glue all the boxes instead of cardboard. To cut out the roof 4 of a triangle, as in the photo – the base 8.6 cm (divide it in half), from the middle of conducting a height of 7 cm, and connect the line to the triangle.
8.6 cm – 2.1 cm is greater than the width of our wall (6 , 5), it is necessary that this number is divisible by 2. If you have a different width, take the size of 2-3 cm more for the roof, it all depends on the size of the house. Here are our billets. The base mark the pen, as the parties have turned out almost identical (in millimeters difference mile), you can get confused. Merge all 4 triangles using masking tape. To box glue strips of masking tape to attach the roof. Like this. As the photo shows that those tape glued side of the box that open (top and bottom). Glued roof.

On the roof,

we draw a vertical line at a height of 1.2 cm and mark the middle of the roof.

Cut to the windows on the roof of the triangles, as in the photo. The first triangle 1 piece, the second – 2 pcs. And so for each window. We have them 3. And in the middle of our window glue mark. And so 3 times. On the fourth side of the roof fastened smoker, but you can make the window 4, as anyone would like. That just happened. Harvesting is ready. Getting modeling. We stuck to the walls of the house first test of about 5-7 mm, splash stack of bricks. Then sculpt the doors and windows. I have 2 of the window. One such – for flowers. Go to the roof. Clung to test about 5-7 mm. Then moisten your fingers in water and straighten all the bumps. It was very difficult to stick round smoker (hard to find), so I had peeled off, clung to the test and draw the stack of stones. And then use the test fastened to the roof. It keeps excellent. Like this. Draw lines on the sides of the roof and windows. The photo can be clearly seen. Simulating tiles – below I’ll show you how it’s done. It is a small house. He had almost dried up. The roof is simple, but after drying, I pasted its eggshell. The windows cut out in advance, then opened the box and glued onto the polymer adhesive piece lace – curtain. Such windows 2. More photos. Next painting. Paint houses completely (except windows) black gouache. Doors and smoker I’m a little rubbed with a wet sponge, then turned to the color lighter. I paint the roof of a large house in a large and small blocks in a reddish-brown color. Brown paint doors and smoke.
Then paint the contrary from the roof of a small house, and a large brick in terracotta color. At the end of the window paint. The bottom of the house is not stuck to the test, as long as will be dry with inversion. To strengthen the bottom, I pasted it into 4 layers of toilet paper with PVA glue. Then painted in black.
The houses covered with lacquer in 2-3 layers. He is blind to the little house orange roses from HF and leaves, for a large house with red roses. I stick to the polymer adhesive. Roses on top of a little gold-colored acrylic paint. Houses are ready !!! Now I tell how I chose the tiles.
The left upper and left lower tiles made using the stack, which is sold with children’s plasticine. You can take a nail file.
The top right – with the help of the cap from the handle, bottom right – with a spatula from a manicure set (I do not use it). That last option I used to roof the house. It has 2 options. And this is done with a fork ( the stacks some effect will be on a toothpick).
You can use orange sticks, a knife, etc. Finally houses separately. Thank you all for your attention

How To Do Canadian Smocking Matrix Design

Sew Fabric 1

The Canadian Smocking Matrix Design is a unique and popular way of creating smocking patterns. It is created by first creating a grid of horizontal and vertical lines on a piece of fabric. Then, the fabric is gathered along the lines to create the desired pattern. This method is often used to create intricate and detailed smocking patterns.

Which is the basic method of Canadian smocking

The basic method of Canadian smocking is the use of a needle and thread to gather fabric together in a decorative way. This is usually done on clothing, such as dresses or blouses, to give them a more fitted appearance.

Learn to Make Canadian Smocking Matrix Design

FAQs

How do you calculate fabric for Canadian smocking?

To calculate the amount of fabric needed for Canadian smocking, you will need to know the dimensions of the area you will be working with. Once you have those measurements, you can determine how much fabric you will need by multiplying the length and width of the area.

Which country developed the smocking stitch?

The smocking stitch was developed in England. This stitch was traditionally used to decorate the yokes of shirts and blouses. Smocking was very popular in the 18th and 19th centuries.

How do you calculate fabric for smocking?

To calculate fabric for smocking, you will need to determine how much fabric you will need for the entire project. To do this, you will need to know the width of the fabric and the length of the fabric. Once you have these measurements, you can calculate the amount of fabric needed by multiplying the width by the length.

How to make beautiful pink angel from bead

pink angel from bead 1

Required Material: the wire is very thin, the best of cable, a little – sm20- silver wire on it will strengthen halo, 1 large white bead for the head. Cap for beads, Round businy5-6 mm. 3mm beads or large beads, preferably rice, but you can do without it,

We print on a piece of the wire length of about 80 cm glass beads and in that order … Keep paetki from the middle were rotated in different directions

Through extreme bead to make a loop … Such loops have to do 5 to 6 pieces

Here is what you should have. Postpone our billet on the skirt

Let us turn to the wings. In the middle of a piece of the wire length of about 50 cm recruit bead 3mm and rising ‘.When using beads, the beads must be a big hole, because, through it, the wire should pass 3 times. Making the top of the wing. Gaining 6 beads and pass through the second of the Risin. We repeat again, each time firmly tightening wire

That’s what happens. Next, we collect 7 beads. Now the loop is obtained from 4-beads

Recruit 5 and beads. missing the top, go through the previous one. In all the work it is the hardest part is necessary as it should tighten the wing. Recruit 2 bead wire and hiking, as photo.Zatem 7 pcs and do a loop of 3 beads

Finally, 12 beads and pass both the two pictures. Do not forget every time tauten provoke.Zatem 5 beads and go through the bead on the rising ‘. Similarly, do another wing. (The longer to write than to do). Lay off the wings and move on to the carcass

In the middle of the wire about 30 cm long bead stringing. Then both ends are passed through a cap for beads and large beads Risin. We are pushing the ends of the wire

We form the handle and tighten bead 4-5mm

Tightly-to-back wings and putting a whole bunch of wire is passed through a bead

Twist the carcass and skirt. That’s our angel looks from above,

And under her skirt

Then we make out the bottom, catching beads on a thin wire, twist and hide the ends

To fasten the waist halo. It turned out Angel. Under this scheme, you can make a fairy, butterfly (changing the wings), but you never know what the imagination will suffice.

 Thank you inspected and read to the end. If someone decide to do or have any questions – please contact. It is not necessary to follow exactly the pattern – this is just an idea. How to translate it – you decide

How to make beautiful wings for pupa and tail for mermaid

pupa and tail for mermaid 1

I want to share with you, my findings, how to make the beauty of the most simple and accessible …
For a start, marker draw our tail or wing in half to split files.

From wire mode and glue (glue “Globe”) frame.

PVA glue smear wire and put on her organza (pieces of old tulle)

Take the soldering iron at her husband, if not then the needle or nail (heated over the fire).
CAUTION Palchikov not to burn !!!
Making holes.

Clay of Melt or thick PVA droplets impose delays on the edge

contrast PAP can outline them with acrylic or gouache.

Well, know each of us has a hairspray, (then it will be transparent), you can PVA water razbavlennoe.Bryzgaem on the wing and immediately sprinkle blёstochkami.

And then, anything sticking pebbles, beads, rhinestones for nail …

That’s how it will look on your pupae

Good luck and inspiration !!!

How to make fragrant teapots – Step By Step

fragrant teapots 1

For we need: knitting fabric good extensibility (possible old sweater jacket small structures.) Smooth or textured monochrome or color, scissors, thread. needle, dense cardboard or plastic (can be washed), holidayer, honey. Clip version of small details and their holo fay erom filling.

Patterns of main parts: the body, the spout, teapot handle.

Fold in half and sewn on the machine, leaving open space. (see photo).

We gut-wrenching detail.

We fill holo fay erom. The open ends of the handle Refill inside. Housing teapot collect on the thread and pull off both sides.

Public allowances refueled inside and sutured. Just do the other side.

Open the edge of the spout is also slightly contractible on a string to the contents do not fall out, and for the convenience of sewing to the body.

We need two more parts: a base and a lid for the teapot. To do this, cut out of cardboard, but it’s better plastic two rounds, their size may be different, it depends on what type of teapot you are doing, but the circles must not be greater than the body diameter. From jersey of a different color or the same cut out more circles of 1, 5 cm.

Putting on a string and well contractible. On the lid, you can put the first filler, then circle out of cardboard, and then pulled away.

Type of finished parts lids and bottoms. Bedplate should be flat.

We work with the body. Long needle and thread connecting the two poles and contractible, but not much. Repeat step two – three times and fasten thread.

It turns bullseye effect. This is necessary to ensure that the finished product does not deform, teapots giving the flattened appearance and for easy sewing peripheral parts.

We begin collecting kettle

Blind stitch sews bottom of a first, then the cap, and then later the spout and handle.

A blind stitch is sewn twice. First stitches larger, second time Mellen Kimi.

Our tea is collected.

A bit of spice …

You can do this …

How to make organizer for jewelry in the form of coral – Step By Step

organizer for jewelry in the form of coral 1

Take a piece of cardboard A4, attach a picture of the future of coral-organizer …

image rendered specifically for printing, so feel free to download and print this pattern … or draw a …

all drawing on a path through a needle … to figure turned with 2 sides … the more often put the holes, the more accurate the drawing will …

Speaking of thin corrugated cardboard take the inside, I took the doll from the packaging …

a cardboard base the future of coral, it is desirable to enclose another piece of the same board, because we will pierce through and through, that needle is easily entered, it is better to enclose something ..

So get ready

further connect the holes … ie on the planned cuts through the loop …

on the reverse side and draw out …

and gently remove unwanted parts …

what happened …

Further take the box, cut it …

try on a coral …

crop, glue …

edge coral paste mint

middle and paste … draping a little paper …

texture of ready undertake the box …

paste, and it is also …

paint pink (or any other) acrylic coral … a box under the rings in the color of the seabed … ie ocher …

toning curves coral darker color from the main … to volume effects …

We draw the work piece surface coral … holes, spots …
white acrylic draws the porosity …

maroon paint pores in the pits …

operate with the bottom cut out a piece of cardboard … 2-3 mm less than the base of each. hand …

We do … puts a pillow under the cardboard padding polyester, tight cloth “on the sand” …

glue in a box …

decorate the bottom … of ruffled green fabric cut out foliage and form bushes ..

side boxes paste stones ….

stones can be laid around the perimeter …

and add Marbles …

from Fimo or any other plastic lepim shells and sea stars … if there is a natural sea shells, you can use them

place seashells and stars on the seabed …

volume loop draw a grain of sand on the fabric … for more decorative …

like that….

add animals to our coral reef …
fish ….
I take the glass eyes of two colors, white acrylic base color the brightness …

of gypsum mass sculpt

heir bright paints …

each fish glued on the stem of a twisted paper …
and placed them on the reef …

left enrich reef decorations …. ie to use it for its intended purpose …

rings on a pillow …

Thank you for your attention and wish you success and creative ideas

How to sew fairy beauty – Step by step

How to sew fairy beauty featured
Fairy beauty – my version keeper cotton discs and sticks. Idea-keepers dolls cotton discs and sticks is not new, but I’ll show you my version of this beautiful and necessary pupa. My keeper almost everything is different from the traditional tilde, from it there was only myself storage idea. If you want to get yourself or as a gift is not only beautiful, but also practical doll, my master class can be helpful. Let’s get started!

Required Materials:
  • Cotton fabric for the body and dress dolls. I prefer natural fabrics from America, Germany, Korea, Japan. For this pupa I took German and American tissue mint and gray colors.
  • Sewing thread to match the fabric. For the body and head dolls, it is desirable to use a strong thread to avoid tearing during stuffing. I like reinforced, 45 pp.
  • Filler for the doll. This can be sintepuh, hollofayber. I use hollofayber.
  • Cotton lace to decorate the doll dress.
  • Waxed cord or other strong cord to create attachment.
  • Elastic underwear width of 0.5 cm to the removable skirt.
  • Wool Felting – for doll hair.
  • Two buttons for hanging cotton discs.
  •   Packing cotton discs. I am using in their pupae packing on 80 disks, they are well suited to my height fairies.
  • Jar with cotton buds. I chose a jar of 100 sticks, it is small and does not look bulky in small puppet handles.
  • Artificial lashes for dolls.
  • Materials for decoration jars with cotton buds. It all depends on your imagination. Shells, marine items, decorations of plastic, foamirana, wood, fabric, lace and so on – the list is endless. For the pupa of the master class, I took a few flowers and leaves of the apple foamirana.

Tools and supplies:
  • Sewing machine. With a strong desire, you can do without it, but the machine greatly facilitates the process.
  • Needles, pins conventional and English
  • Scissors: Manicure, fabric and pinking (zig-zag) if there is. Also for cutting threads convenient to use scissors-snippery
  • Needle Felting.
  • Acrylic paints.
  • Acrylic lacquer.
  • Brushes: thin – for painting the face and thicker – for varnishing.
  • Dry pastel – for toning the face doll.
  • Tools for packing. I use a stick to sushi.
  • Glue: Transparent versatile, super-glue, fabric, PVA glue.
  • A piece of cardboard or plastic bottoms.
  • A small piece of soft lint-free cloth. I have a fleece.
  • Washed off or Disappearing marker for tissue or tailor’s pencil – for transferring the pattern onto the fabric. I use a pencil, because it leaves a thin line.
  • Thin double sided tape.
  • Simple pencil.
  • Pattern. For each pupa I am a little changing the pattern, so working patterns I have a few. Here’s a variation of one of them: